Connecting iPad to BSNL network using DNA-A211- modemI

[saktibagchi]

Hi,I have got one iPad2 yesterday. I use DNA-A211-I modem to connect to internet from my laptop. My laptop directly connects to the modem as soon as start my laptop. Then I connect to broadband dialup icon to enter user name and password which connects me to internet.iPad is recognising my wireless modem and connecting too. But how would I connect to broadband? I read in this forum the ways to configure the modem by entering user name and password etc but it is not helping much.Please help.

 

[Babhishek]

Buy a wireless router

 

[netant]

Hi,

I have got one iPad2 yesterday. I use DNA-A211-I modem to connect to internet from my laptop. My laptop directly connects to the modem as soon as start my laptop. Then I connect to broadband dialup icon to enter user name and password which connects me to internet.
iPad is recognising my wireless modem and connecting too. But how would I connect to broadband?
I read in this forum the ways to configure the modem by entering user name and password etc but it is not helping much.
Please help.
use PPPoE mode inside the DNA-A211-I to connect to Internet then you have Internet everywhere.

to do that login to your modem & put these settings

PVC Number – PVC 0
Connection Type – PPPoE
VPI/VCI – 0 / 35
User Name –
Password –

 

[saktibagchi]

use PPPoE mode inside the DNA-A211-I to connect to Internet then you have Internet everywhere.

to do that login to your modem & put these settings

PVC Number – PVC 0
Connection Type – PPPoE
VPI/VCI – 0 / 35
User Name –
Password –




Thank you for your response.

Yes I did above but still just connecting to the wifi is not helping. Even when I am using Laptop, just connecting to wifi is not giving me internet access. I have to click on dia;up icon to enter username and password to connect to internet.

Device Info

Board ID: 96338W-20P2
Software Version: 3.08.02.IB.02.01_1701_022709
Bootloader (CFE) Version: 1.0.37-10.1
Firmware Version: DNA-A211-I-0001.01
Hardware Version: DNA-A211-I 2.6
Model Name: DNA-A211-I
Wireless Driver Version: 3.131.35.6.cpe2.0a.s

This information reflects the current status of your DSL connection.


Line Rate - Upstream (Kbps): 509
Line Rate - Downstream (Kbps): 2045
LAN IP Address: 192.168.1.1
Default Gateway:
Primary DNS Server: 192.168.1.1
Secondary DNS Server: 192.168.1.1

ATM PVC Configuration
This screen allows you to configure an ATM PVC identifier (VPI and VCI) and select a service category. Otherwise choose an existing interface by selecting the checkbox to enable it.

VPI: [0-255] 0
VCI: [32-65535] 35


Enable VLAN Tagging

Service Category: UBR Without PCR

Enable Quality Of Service

Connection Type

Select the type of network protocol for IP over Ethernet as WAN interface

PPP over ATM (PPPoA)

PPP over Ethernet (PPPoE)

MAC Encapsulation Routing (MER)

IP over ATM (IPoA)

Bridging


Encapsulation Mode

LLC/SNAP-BRIDGING VC/MUX


In the next screen I have netered my broadband user name and password.

Bridge PPPoE Frames Between WAN and Local Ports (Default Enabled) option is checked.

Summary:

WAN Setup - Summary

Make sure that the settings below match the settings provided by your ISP.

VPI / VCI: 0 / 35
Connection Type: PPPoE
Service Name: pppoe_0_35
Service Category: UBR
IP Address: Automatically Assigned
Service State: Enabled
NAT: Enabled
Firewall: Enabled
IGMP Multicast: Disabled
Quality Of Service: Enabled

In LAN Set up:

Enable DHCP Server is checked.

Is there anything else I am missing.