BSNL PPPoE not working

[flashmani]

Hi,My BSNL connection is not working for past 7 days. BSNL is saying there is some prob in my modem. I went to D-Link service center my modem was working fine. They are saying there is prob is BSNL line. I am really frustrated that i called BSNL almost 50 times...Can anybody tell me where is prob. Please help me....Here is my modem status...GLB-502TModem Status -------------------------------------------- Connection Status Connected Us Rate (Kbps) 303 Ds Rate (Kbps) 4160 US Margin 6 DS Margin 6 Trained Modulation ADSL_2plus LOS Errors 0 DS Line Attenuation 34 US Line Attenuation 16 Peak Cell Rate 714 cells per sec CRC Rx Fast 5 CRC Tx Fast 0 CRC Rx Interleaved 0 CRC Tx Interleaved 0 Path Mode Interleaved DSL Statistics Near End F4 Loop Back Count 0 Near End F5 Loop Back Count 0 --------------------------------------------- Connection StatusDescription Type IP State Online Disconnect Reason BSNL pppoe N/A Not Connected 0 N/A -------------------------------------------------------System log--------------------DSL Polling Timer Started succesfully.Firewall NAT service starteddel_iptable_rules : ppp_name not intact updateall_servers : No children found for conn:Bridge Created: br0Bridge Created: br1Bridge Interface Added: eth0Bridge Interface Added: usb0DSL Carrier is downdel_iptable_rules : ppp_name not intact DSL Carrier is trainingdel_iptable_rules : ppp_name not intact DSL Carrier is trainingdel_iptable_rules : ppp_name not intact DSL Carrier is upauto_vcc_default oamPing(0.35)result(2)auto_vcc_default oamPing(0.32)result(2)auto_vcc_default oamPing(0.40)result(2)auto_vcc_default oamPing(0.36)result(2)auto_vcc_default oamPing(0.38)result(2)auto_vcc_default oamPing(0.96)result(2)auto_vcc_search oamPing(0.35)result(2)auto_vcc_search oamPing(8.35)result(2)auto_vcc_search oamPing(0.43)result(2)auto_vcc_search oamPing(0.51)result(2)auto_vcc_search oamPing(0.59)result(2)auto_vcc_search oamPing(8.43)result(2)auto_vcc_search oamPing(8.51)result(2)auto_vcc_search oamPing(8.59)result(2)Conn Delay Timer started for 50 secpppd 2.4.1 started by root, uid 0TimerEvent: PPPoE not in a state to handle it; currState 3.ThanksFlashmani

 

[essbebe]

Are you using Dialer or "Always on " mode.Enter UserId without @ bsnl.inPost ipconfig/allRecheck settings:REF: 210.212.160.18/broadband-conf/D-Link.htm

 

[ensine]

Even I was not able to connect since last 4 days. While contacted BSNL, they said that problem was with BSNL. Today they rectify it.

 

[flashmani]

It almost three weeks... nothing happening. One guy has come and saw the connectivity(unfourtuantly the ADSL light was not coming at that time) and asked me to log a complaint for ADSL connectivity....Really i disappointed with BSNL. I enquired with Airtel but there is no port near my home. Actually my modem is GLB 502-T it is different settings page from this "REF: 210.212.160.18/broadband-conf/D-Link.htm"Flashmani

 

[essbebe]

@flashmani
BSNL pppoe N/A Not Connected 0 N/A
Either try dialer mode or PPPoE/PPPoA mode.
Post ipconfig/all data
Start/RUn type cmd type ipconfig/all
GLB502T has DIRECT RJ11 connection.
Connect directly from Phone junction.
Other settings are almost same as dsl502T.
Change mod to GDMT.



FREE today only : Winuitilities useful program.
Giveaway of the Day - free licensed software daily - Spread the Word

 

[flashmani]

Thanks for the replyI am using "PPPoE" "always on" " GLB502T has DIRECT RJ11 connection.Connect directly from Phone junction." - i tried this also..." Change mod to GDMT." - where do i change this.i will post all my setting with screen shot tomm....

 

---

[essbebe]

DLINK GLB-502T ADSL2+ Router configuration for BSNL dataone | I am Sumeet

post ipconfig/all data.

 

[superprash2003]

do you see any error like authentication failure or something?? go to the WAN page and under vpi/vci 0/35 .. set it to bridged mode and create a dialer.. then if you get an error, it would be easier to find out where the problem is..