Sterlite SAM300AX (Unable to forward Port)
- Thread starter Karan_gr8
- Start date
- Replies 12
- Views 6,959
leasehelp:superprash2003
Regulars
do you face any error while port forwarding? look at PortForward.com - Free Help Setting up Your Router or Firewall for tutorials
Even I was never able to forward ports successfully. Those damn p2p clients just didn't work properly. In the end I set my kaspersky internet security firewall to one level above the default low level, enabled DMZ inside my router, finished all my fully legal downloading/uploading, disabled DMZ inside router and then switched the software firewall back to default. There that wasn't so hard was it :thumbsup:
do you face any error while port forwarding? look at PortForward.com - Free Help Setting up Your Router or Firewall for tutorials
Hi, Thanks for reply,
Yes I have tried Port forwarding guide, I've successfully forwarded the port on my modem before (was different modem).
Error I am getting is : An error has occurred!
Port 45682 does not appear to be open.
I've been doing exactly what is written in Port forwarding guide.
Here is what I did and I think that's all I am suppose to do, but its not working
Hi, Thanks for reply,
Yes I have tried Port forwarding guide, I've successfully forwarded the port on my modem before (was different modem).
Error I am getting is : An error has occurred!
Port 45682 does not appear to be open.
I've been doing exactly what is written in Port forwarding guide.
Here is what I did and I think that's all I am suppose to do, but its not working
http://i6.tinypic.com/6ur7rd3.jpg
1.any page like this?
using "dialer" mode or" always On"
silly question! sould be latter. confirm.
2
.Open Port Check Tool
check port/s is/are open.
3.Check Windows Firewall and in any other FW application.
enable this application.
1.any page like this?
using "dialer" mode or" always On"
silly question! sould be latter. confirm.
2
.Open Port Check Tool
check port/s is/are open.
3.Check Windows Firewall and in any other FW application.
enable this application.
superprash2003
Regulars
post output of ipconfig from your windows machine's command prompt
Physical Address. . . . . . . . . :
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.1.14
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 4.2.2.2
59.179.243.70
Physical Address. . . . . . . . . :
Dhcp Enabled. . . . . . . . . . . : No
IP Address. . . . . . . . . . . . : 192.168.1.14
Subnet Mask . . . . . . . . . . . : 255.255.255.0
Default Gateway . . . . . . . . . : 192.168.1.1
DNS Servers . . . . . . . . . . . : 4.2.2.2
59.179.243.70
http://i6.tinypic.com/6ur7rd3.jpg
1.any page like this?
using \"dialer\" mode or\" always On\"
silly question! sould be latter. confirm.
2
.Open Port Check Tool
check port/s is/are open.
3.Check Windows Firewall and in any other FW application.
enable this application.
1. I am not using Dialer, Connection is always on.
2. Port is not open.
3. Not using windows firewall and using AVG FREE (I dont think it has Firewall)
1.any page like this?
using \"dialer\" mode or\" always On\"
silly question! sould be latter. confirm.
2
.Open Port Check Tool
check port/s is/are open.
3.Check Windows Firewall and in any other FW application.
enable this application.
1. I am not using Dialer, Connection is always on.
2. Port is not open.
3. Not using windows firewall and using AVG FREE (I dont think it has Firewall)
superprash2003
Regulars
if your using this port for a torrent client.. then make sure the client is running when you check for open ports