BSNL ONT bypass - Getting PADI Timeout error

  • Thread starter Thread starter amohan78
  • Start date Start date
  • Replies Replies 14
  • Views Views 201
Messages
22
Location
KOLKATA
ISP
JIO
Dear All

I have a BSNL FTTH connection which runs 2 VLAN, VLAN 200 for Internet and VLAN 201 for Voice. I have got a Syrotech modem which is configured by BSNL. The TR069 is configured.

Now I decided to dump the Syrotech modem. So I purchased TP-Link XZ000-G7 ONU and TP Link ER605 Dual WAN Loadbalancer.
In XZ000-G7,
1. I copied the Syrotech Serial Number and applied the same on the Serial Number field of XZ000-G7. This made the device PON light stable and Connection state as O5.
2. Then I put the VLAN setting of this XZ000-G7 as TRANSPARENT MODE. Which effectively means Bridge Mode.

The LAN Port of XZ000-G7 was connected to Port 1 of TP Link ER605. Port 1 is a WAN port.
In TL-ER605
1. I configured PPPoE on WAN 1, gave the username and password, MTU as 1492, VLAN as 200 and hit Save.
2. Then I changed the WAN MAC to the same MAC as that of Syrotech ONT which BSNL provided.

The connection is not getting established. On the log, the following error is displayed

PPPoE ctXXXXXXXXX_eid@ftth.bsnl.in failed to connect to the server because sending PADI times out

Can anyone help me out what is this error and why I am getting this ? What can be the solution for this error ?
 
@sloj

Thank you for bringing this to my attention. That gentleman was lucky that it was no PADI error. The authentication was a simple error to fix. I have GPON registered and still I am struggling.
 
@amohan78 yes you will get many of them. I config'd Syrotech to bridge to my openwrt router and it takes a long time for the BRAS to reply. Once replies arrive you will get connected very fast.

You'll have to wait and watch. Otherwise, see if re-connecting the syrotech router gives you internet first (or if you've been mac banned and need a mac reset).

To bridge from syrotech directly:

1. note down the Mac for the internet profile
2. create a new profile and hit save (don't fill anything)
3. delete the internet profile
4. on the new profile that you made select mode as bridge, and enter the vlan for internet
5. select one of the router ports and then hit save
6. connect to your new router and profit

You need the new profile (before deleting the old one) is because the router will detect a mac loop and end up unauthorizing the connection to the OLT directly, then you will need to contact LCO for mac reset. Making new profile first will let it select the next mac available to it, avoiding this issue.

Once you verify this works shift to the TP-Link bridge.
 
@thatayush That is a great reply for me to look at. I see this is working as per your instruction.

There is in fact one very interesting follow up question for you. BSNL gives two VLANs, one for the Internet+TR069 and another VLAN for the VoIP or the Voice.
I have been able to take the Syrotech ONT to work in bridge mode for the INTERNET profile and VLAN and thereby make it land on TP-Link router as the PPPoE dialer.
But I am not able to make both the VoIP and INTERNET VLANs pass as a bridge to TP Link. My intention was to receive both the VLANs in Tp Link and then split it in 2 different ports (via IPTV/VOIP config), one will be the Internet WAN and the other one will be a VoIP Bridge. The port which will be a VoIP bridge port will be connected to an IP phone for Voice.

So now, I can only take the INTERNET VLAN to land in TP LINK and create PPPoE connection in TP LINK. The VoIP VLAN is unable to come over.

I have created 2 bridge connection containing 2 VLAN INTERNET and VoIP , done VLAN mapping to the LAN port and then mentioned the same VLAN number for INTERNET profile in the PPPoE WAN connection. This is not working and giving that PADI Timeout.

But if I just pass only one VLAN and create the PPPoE connection with no VLAN mentioned, it works as you have suggested.
 
@amohan78 ah that's not possible with the Syrotech router since it doesn't have the functionality to be used as a transparent bridge. Instead you can see if using the 2nd router port will work in that scenario. Ideally you want to make it so that the xz000-g7 works as a transparent bridge. Worst case scenario this 2 cable syrotech method is what you use...

Edit: actually you can try doing fun things with routing by adding a dhcp interface with non-tagged port (while keeping pppoe on tagged port) and see if that works. You'll have to add a static route in the syrotech.
 
@thatayush Thanks for your answer. In fact the second part which you wrote was my ultimate objective to achieve. Unfortunately that is something I do not thing I will be able to get because of how Syrotech router works.

I had kept the syrotech router aside and tried one hack. as you know XZ000-G7 has the transparent mode. So i took out the BSNL fiber patch cord and inserted into the XZ000-G7 PON port and spoofed the Serial Number. PON got stabilised. Then I put its VLAN setting to Transparent. Then I connected the G7 LAN port to WAN port on TP-Link and made the IPTV/VLAN splitting to create a LAN port for the VoIP and the tagged trunk port to PPPoE dial up. unfortunately that did not work ! PADI timeout killed the entire fun,
 
Back